|
Analysis of a Micro Gas Turbine Fed by Natural Gas and Synthesis Gas: Test Bench and Combustor CFD Analysis [GT2011‑46090] |
|
Validation of Numerical Simulation for Rotating Stall in a Transonic Fan [GT2011‑46109] |
|
CFD Analyses of HPT Blade Air Delivery System With and Without Impellers [GT2011‑45949] |
|
Measurement of a Benchmarking Jet in Crossflow Configuration Under Highly Turbulent Conditions [GT2011‑45262] |
|
PIV Study on the Dimple Mid-Plane of a Narrow Rectangular Channel With Dimples Applied to One Wall [GT2011‑46132] A Study of Heat Transfer Augmentation for Recuperative Heat Exchangers: Comparison Between Two Dimple Geometries [GT2011‑46401] |
|
Performance Analysis of a Microturbine Centrifugal Compressor From a Manufacturing Perspective [GT2011‑46374] |
|
Numerical Study of Non-Reacting and Reacting Flow Characteristics in a Lean Direct Injection Combustor [GT2011‑45263] Gas Path Analysis on KLM In-Flight Engine Data [GT2011‑45625] |
|
Three Dimensional Design and Optimization of Transonic Rotor in Axial Flow Compressors [GT2011‑45425] |
|
Life Assessment by Fracture Mechanics Analysis and Damage Monitoring Technique on Combustion Liners [GT2011‑46107] |
|
The Simulation of an Axial Flow Fan Performance Curve at Low Flow Rates [GT2011‑45709] |
|
LES of Pre-Vaporised Kerosene Combustion at High Pressures in a Single Sector Combustor Taking Advantage of FGM [GT2011‑45819] |
|
E-Class DLN Technology Advancements, DLN1+ [GT2011‑45944] |
|
Exhaust Gas Recirculation Performance in Dry Low Emissions Combustors [GT2011‑46482] |
|
Optimization of a U-Bend for Minimal Pressure Loss in Internal Cooling Channels: Part I—Numerical Method [GT2011‑46541] Optimization of a U-Bend for Minimal Pressure Loss in Internal Cooling Channels: Part II—Experimental Validation [GT2011‑46555] |
|
Analysis of the Effects of Parallel and Angular Misalignment in Hyperstatic Rotors Equipped With Oil-Film Bearings [GT2011‑45903] Modeling of the Dynamic Response of a Pelton Turbine Hydroelectric Plant [GT2011‑45907] Effects of Thermal Transients on Cracked Shaft Vibrations [GT2011‑46181] Effects of the Shaft Normal Modes on the Model-Based Identification of Unbalances in Rotating Machines [GT2011‑46184] |
|
Rotordynamic Force Coefficients for Three Types of Annular Gas Seals With Inlet Preswirl and High Differential Pressure Ratio [GT2011‑45556] Numerical Simulation and Full Scale Landing Test of a 12.5 MW Vertical Motorcompressor Levitated by Active Magnetic Bearings [GT2011‑46411] |
|
Stability Analysis of an Industrial Gas Compressor Supported by Tilting-Pad Bearings Under Different Lubrication Regimes [GT2011‑46450] |
|
Computation of Aerodynamic Damping for Flutter Analysis of a Transonic Fan [GT2011‑46597] |
|
On a Numerical Method for the Simulation of Steady Jet Array Interaction With Rotating Components [GT2011‑45832] |
|
Design and Optimization of a High Temperature Water Cooled Probe for Gas Analysis Measurement on K11 Combustion Test Rig [GT2011‑45177] |
|
Influence of Surface Roughness on the Profile and End-Wall Losses in Low Pressure Turbines [GT2011‑46371] |
|
DNS of Stagnation Point Heat Transfer Affected by Varying Wake-Induced Turbulence [GT2011‑45312] |
|
F-Class DLN Technology Advancements: DLN2.6+ [GT2011‑45373] |
|
Turbulent Consumption Speed Scaling of H2/CO Blends [GT2011‑45401] |
|
Development of a Statistical Methodology for Gas Turbine Prognostics [GT2011‑45708] Application of Forecasting Methodologies to Predict Gas Turbine Behavior Over Time [GT2011‑45710] |
|
Technical and Economic Evaluation of IGCC Systems Using Coal and Petroleum Coke Considering the Brazilian Scenario [GT2011‑46836] |
|
Predicting Blade Leading Edge Erosion in an Axial Induced Draft Fan [GT2011‑45719] |
|
Gas Path Analysis on KLM In-Flight Engine Data [GT2011‑45625] |
|
Application of Dielectric Barrier Discharge to Improve the Flashback Limit of a Lean Premixed Dump Combustor [GT2011‑45161] |
|
Aerodynamic Characterization of Transonic Turbine Vanes Optimized to Attenuate Rotor Forcing [GT2011‑46553] |
|
Three Dimensional Design and Optimization of Transonic Rotor in Axial Flow Compressors [GT2011‑45425] Optimization of a U-Bend for Minimal Pressure Loss in Internal Cooling Channels: Part I—Numerical Method [GT2011‑46541] Optimization of a U-Bend for Minimal Pressure Loss in Internal Cooling Channels: Part II—Experimental Validation [GT2011‑46555] |
|
Study of Unforced and Modulated Inclined Film-Cooling Jets Using Proper Orthogonal Decomposition: Part I—Unforced Jets [GT2011‑45400] Study of Unforced and Modulated Inclined Film-Cooling Jets Using Proper Orthogonal Decomposition: Part II—Forced Jets [GT2011‑46901] |
|
Engine Design Strategies to Maximize Ceramic Turbine Life and Reliability [GT2011‑46784] |
|
Genetic Algorithm for Gas Turbine Blading Design [GT2011‑46171] |
|
A Competitive Market Approach to Gas Turbine Technology Portfolio Selection [GT2011‑45989] |
|
Mu Analysis for Turbomachinery Stall Flutter [GT2011‑46624] |
|
Gas Path Analysis on KLM In-Flight Engine Data [GT2011‑45625] |
|
Influences of Inlet Swirl Distributions on an Inter-Turbine Duct: Part I—Casing Swirl Variation [GT2011‑45554] Influences of Inlet Swirl Distributions on an Inter-Turbine Duct: Part II—Hub Swirl Variation [GT2011‑45555] |
|
Application of Dielectric Barrier Discharge to Improve the Flashback Limit of a Lean Premixed Dump Combustor [GT2011‑45161] Effect of Tip Clearance on the Prediction of Non-Synchronous Vibrations in Axial Compressors [GT2011‑45392] |
|
Investigation of the Tip Clearance Flow in a Compressor Cascade Using a Novel Laser Measurement Technique With High Temporal Resolution [GT2011‑45176] Impact of Manufacturing Variability and Non-Axisymmetry on High-Pressure Compressor Stage Performance [GT2011‑45718] |
|
Investigation of Unsteady Compressor Flow Structure With Tip Injection Using Particle Image Velocimetry [GT2011‑45281] Investigation of Passage Flow Features in a Transonic Compressor Rotor With Casing Treatments [GT2011‑45364] |
|
Experimental and Numerical Investigation of Mistuned Aerodynamic Influence Coefficients in an Oscillating LPT Cascade [GT2011‑46283] |
|
Effect of Scaling of Blade Row Sectors on the Prediction of Aerodynamic Forcing in a Highly-Loaded Transonic Turbine Stage [GT2011‑45813] Influence of the Blade Count Ratio on Aerodynamic Forcing: Part II—High Pressure Transonic Turbine [GT2011‑46071] Prediction of Turbomachinery Aeroelastic Behavior From a Set of Representative Modes [GT2011‑46690] |
|
Altitude Testing of the E3E Core Engine [GT2011‑45876] |
|
Improving the Application of Turbine Maps in 1D Engine Process Modelling [GT2011‑45500] |
|
Impact of Manufacturing Variability and Non-Axisymmetry on High-Pressure Compressor Stage Performance [GT2011‑45718] |
|
Diagnostics of Highly Degraded Industrial Gas Turbines Using Bayesian Networks [GT2011‑45249] |
|
Combined Effects of Wakes and Pulsed Vortex Generator Jet Flow Control on Boundary Layer Separation on a Very High Lift Low Pressure Turbine Airfoil [GT2011‑46106] |
|
Experimental and Numerical Investigation of Flow Field and Downstream Surface Temperatures of Cylindrical and Diffuser Shaped Film Cooling Holes [GT2011‑45106] Application of a CFD-Based Film Cooling Model to a Gas Turbine Vane Cascade With Cylindrical and Shaped Hole Endwall Film Cooling [GT2011‑45117] |
|
Numerical Optimization of a Steam Turbine Control Stage by Flowpath Profiling Using Evolutionary Algorithm [GT2011‑46237] |
|
The Simulation of an Axial Flow Fan Performance Curve at Low Flow Rates [GT2011‑45709] |
|
DNS of Stagnation Point Heat Transfer Affected by Varying Wake-Induced Turbulence [GT2011‑45312] |
|
CFD Simulations of Flow and Heat Transfer in a Pre-Swirl System: Influence of Rotating-Stationary Domain Interface [GT2011‑45085] Heat Transfer in an Oblique Jet Impingement Configuration With Varying Jet Geometries [GT2011‑45169] |
|
Theory and Application of Axisymmetric Endwall Contouring for Compressors [GT2011‑45624] |
|
Modeling of Inlet Distortion Using a Combined Turbofan and Nacelle Inlet Model During Crosswind and Low Speed Forward Operation [GT2011‑46466] CFD Analysis and Full Scale Testing of a Complex Auxiliary Power Unit Intake System [GT2011‑46748] |