|
Gas Turbines CHP for Bioethanol and Biodiesel Production Without Waste Streams [GT2011‑46683] |
|
Experimental Investigation on Leakage Losses and Heat Transfer in a Non Conventional Labyrinth Seal [GT2011‑46362] |
|
The Influence of Blade Sweep Technique in Linear Cascade Configuration [GT2011‑45728] |
|
A Statistical Characterization of the Effects of Mistuning in Multi-Stage Bladed Disks [GT2011‑46698] |
|
Implementation of a Multi Zone Radiation Method in a Low NOx Gas Turbine Combustion Chamber Conceptual Simulator [GT2011‑46380] |
|
Numerical Characterization of Aerodynamic Losses of Jet Array for Gas Turbine Applications [GT2011‑46212] Analysis of Gas Turbine Rotating Cavities: Estimation of Rotor Disk Pumped Mass Flow Rate [GT2011‑46225] Experimental Investigation on Leakage Losses and Heat Transfer in a Non Conventional Labyrinth Seal [GT2011‑46362] |
|
Aerodynamic Redesigning of an Industrial Gas Turbine [GT2011‑46258] |
|
Comparison of the Steady-State and Dynamic Performance of Two Fixed-Geometry Journal Bearings [GT2011‑46761] Effect of Surface Texturing on the Steady-State Properties and Dynamic Coefficients of a Plain Journal Bearing: Experimental Study [GT2011‑46804] |
|
Synthetic Jet Fuel Combustion: Experimental and Kinetic Modeling Study [GT2011‑45234] |
|
Conceptual Design of a Mid-Sized Semi-Closed Oxy-Fuel Combustion Combined Cycle [GT2011‑46299] |
|
Transition Mechanisms in Laminar Separated Flow Under Simulated Low Pressure Turbine Airfoil Conditions [GT2011‑45690] |
|
Vibration Control of a Turbo Molecular Pump Suspended by Active Magnetic Bearings [GT2011‑45785] |
|
Modeling and Control System Design of a Marine Condensing System [GT2011‑45959] Numerical Investigation and Performance Optimization of an Air-Cooled Steam Condenser Cell Under Ambient Conditions [GT2011‑46030] Dynamic Analysis of a Wind Energy Storage System in Remote Offshore Areas [GT2011‑46058] |
|
Optimization of 6.2:1 Pressure Ratio Centrifugal Compressor Impeller by 3D Inverse Design [GT2011‑46505] |
|
Simulation of Confined Co-Flow Methane-Air Diffusion Flame Under Microgravity Condition With Variable Property Formulation [GT2011‑45486] |
|
Design and Analysis of a New Accessory Gearbox Housing for a Gas Turbine Engine [GT2011‑46747] |
|
Passive Absorption/Emission Spectroscopy for Gas Temperature Measurements in Gas Turbine Engines [GT2011‑45152] |
|
Heat Transfer, Hydrodynamics and Pressure Drop in the Model of a Blade Leading Edge Cyclone Cooling [GT2011‑45150] |
|
Heat Transfer and Friction Factor in the Rib Roughened Blade Leading Edge Cooling Passage [GT2011‑45434] |
|
An Experimental Study of Thermal Barrier Coatings and Film Cooling on an Internally Cooled Simulated Turbine Vane [GT2011‑46604] |
|
Investigation of the Effects of Inlet Swirl on Compressor Performance and Operability Using a Modified Parallel Compressor Model [GT2011‑45553] |
|
Evaluating Complex Inlet Distortion With a Parallel Compressor Model: Part 2—Applications to Complex Patterns [GT2011‑45068] |
|
Evaluating Complex Inlet Distortion With a Parallel Compressor Model: Part 1—Concepts, Theory, Extensions, and Limitations [GT2011‑45067] |
|
Altitude Performance of a Turbojet With Alternate Fuels [GT2011‑45132] Emissions Assessment of Alternative Aviation Fuel at Simulated Altitudes [GT2011‑45133] |
|
Prediction of Turbine Rotor Blade Forcing due to In-Service Stator Vane Trailing Edge Damage [GT2011‑45204] |
|
A Validation of Commerical Flow Solver Performance on Hybridised Octree Meshes [GT2011‑45713] |
|
Stall Warning by Blade Pressure Signature Analysis [GT2011‑45850] Self Regulating Casing Treatment for Axial Compressor Stability Enhancement [GT2011‑46042] |
|
Limits on Morrow Mean Stress Correction of Manson-Coffin Life Prediction Models [GT2011‑45444] |
|
Single and Multi Objective CFD Optimization of Horizontal Axis Wind Turbines [GT2011‑45607] Development and Testing of Sustainable Refrigeration Plants [GT2011‑45609] |
|
Life Assessment by Fracture Mechanics Analysis and Damage Monitoring Technique on Combustion Liners [GT2011‑46107] |
|
A New Hybrid Method for Wind Power Forecasting Based on Wavelet Decomposition and Artificial Neural Networks [GT2011‑46382] Performance Improvement of Turbomachinery Using Plasma Actuators [GT2011‑46413] |
|
LES and RANS of Premixed Combustion in a Gas-Turbine Like Combustor Using the Flamelet Generated Manifold Approach [GT2011‑46355] |
|
Gas Turbine Bottoming Cycles for Cogenerative Applications: Comparison of Different Heat Recovery Cycle Solutions [GT2011‑46236] |
|
Forced Flame Response of a Lean Premixed Multi-Nozzle Can Combustor [GT2011‑46080] |
|
Parametric Study of Bump Foil Gas Bearings for Industrial Applications [GT2011‑46767] |
|
Implementation of a Multi Zone Radiation Method in a Low NOx Gas Turbine Combustion Chamber Conceptual Simulator [GT2011‑46380] |
|
Highly Loaded LPC Blade and Non Axisymmetric Hub Profiling Optimization for Enhanced Efficiency and Stability [GT2011‑46261] |
|
Fluid-Structure Interaction Using a Modal Approach [GT2011‑45692] |
|
Engine Parameter Estimation in Test Cells Using Hybrid Physics/Empirical Models [GT2011‑45633] |
|
An Experimental Study of Thermal Barrier Coatings and Film Cooling on an Internally Cooled Simulated Turbine Vane [GT2011‑46604] Overall and Adiabatic Effectiveness Values on a Scaled Up, Simulated Gas Turbine Vane: Part I—Experimental Measurements [GT2011‑46612] Overall and Adiabatic Effectiveness Values on a Scaled Up, Simulated Gas Turbine Vane: Part II—Numerical Simulations [GT2011‑46616] The Effects of Conjugate Heat Transfer on the Thermal Field Above a Film Cooled Wall [GT2011‑46617] |
|
Shock Propagation and MPT Noise From a Transonic Rotor in Non-Uniform Flow [GT2011‑45645] |
|
Analytic Modelling of Floating Ring Annular Seals [GT2011‑46047] |
|
Combustion Hardware Extendor Kit III Enhancement Kit for MS5002C and D Heavy Duty Gas Turbine for Oil and Gas Applications [GT2011‑46512] |
|
The ORegen™ Waste Heat Recovery Cycle: Reducing the CO2 Footprint by Means of Overall Cycle Efficiency Improvement [GT2011‑45051] |
|
A Novel Bulk-Flow Model for Improved Predictions of Force Coefficients in Grooved Oil Seals Operating Eccentrically [GT2011‑45274] Rotordynamic Force Coefficients for Three Types of Annular Gas Seals With Inlet Preswirl and High Differential Pressure Ratio [GT2011‑45556] |
|
Application of an Inverse Cascade Analytical and Numerical Design Method Used in the Design of Axial Fans [GT2011‑45860] Extended Mean Line Theory for Axial Fans: Analytic Calculation of the Flow Characteristics for Off-Design Points [GT2011‑46268] Design of Axial Fans Considering the Accurate Calculation of the Slip Factor of Axial Flow Cascades and Full Three Dimensional Axial Impellers for Arbitrary Blade Shapes [GT2011‑46352] |
|
Qualification Testing of a Liquid CO2 Turbopump for Carbon Capture and Sequestration Applications [GT2011‑45912] Determination of Residual Stresses on a Centrifugal Compressor Impeller [GT2011‑46601] |
|
Multiscale Partially Averaged Navier Stokes Approach for the Prediction of Flow in Linear Compressor Cascade With Moving Casing [GT2011‑45875] |
|
Process Integration and Automated Numerical Design Optimization of an Eigenfrequency Analysis of a Compressor Blade [GT2011‑45489] |
|
Experimental Analysis of Confined Jet Flames by Laser Measurement Techniques [GT2011‑45111] |
|
Stiffness Measurement for Pressure-Loaded Brush Seals [GT2011‑45399] |
|
Viscous Controlled Vortex Design and Optimization of a 1.5-Stage Axial Subsonic Test Turbine [GT2011‑46113] The Numerical Simulation of Inlet Fogging Effects on the Stable Range of a Transonic Compressor Stage [GT2011‑46124] |
|
Numerical Investigation on Rotor Tip Leakage Control by Casing Air Injection for a Radial Inflow Turbine [GT2011‑46123] Integrated Optimization Design for a Radial Turbine Wheel of a 100kW-Class Microturbine [GT2011‑46140] |
|
Time-Accurate Calculations of a Passive Shroud Bleed Configuration and Implications for Unsteady Blade Loading [GT2011‑45777] |
|
Improvement of Oxide/Oxide CMC and Development of Combustor and Turbine Components in the HiPOC Program [GT2011‑45460] |
|
Eddy Current Damper for Turbine Blading: Electromagnetic Finite Element Analysis and Measurement Results [GT2011‑45242] |
|
Flow and Heat Transfer in the Tip-Turn Region of a U-Duct Under Rotating and Non-Rotating Conditions [GT2011‑46013] Effects of Pin-Fin Height on Flow and Heat Transfer in a Rectangular Duct [GT2011‑46014] |
|
Electronic Torsional Vibration Elimination for Synchronous Motor Driven Turbomachinery [GT2011‑46005] Torsional Vibration Protection System [GT2011‑46112] |
|
Rotating Machine Critical Speed Suppressing by Using Electromagnetic Actuators [GT2011‑45598] |
|
Prediction of the Blade Trailing-Edge Noise of an Axial Flow Fan [GT2011‑45256] |
|
Experimental and Analytical Leakage Characterization of Annular Gas Seals: Honeycomb, Labyrinth and Pocket Damper Seals [GT2011‑45217] |
|
Optimization of Temperature Measurement Technique Used in High Heat Flux Environment [GT2011‑45269] |
|
Numerical Study of Non-Reacting and Reacting Flow Characteristics in a Lean Direct Injection Combustor [GT2011‑45263] |
|
ICR350: A Turbine Solution for Medium and Heavy Duty Vehicles [GT2011‑45945] |
|
Hydroprocessed Renewable Jet Fuel Evaluation, Performance, and Emissions in a T-63 Turbine Engine [GT2011‑46572] |
|
The Influence of Inlet Contraction on Vane Aerodynamic Losses and Secondary Flows With Variable Turbulence and Reynolds Number [GT2011‑45737] |
|
Optimization of a 3-Stage Booster: Part 1—The Axisymmetric Multi-Disciplinary Optimization Approach to Compressor Design [GT2011‑46569] Optimization of a 3-Stage Booster: Part 2—The Parametric 3D Blade Geometry Modeling Tool [GT2011‑46664] |
|
Mist/Air Cooling in a Two-Pass Rectangular Rotating Channel With 45-deg Angled Rib Turbulators [GT2011‑45954] |
|
An Analytical Approach to Gas Turbine Engine Model Linearization [GT2011‑45371] Correlation Measure-Based Stall Margin Estimation for a Single-Stage Axial Compressor [GT2011‑46326] Impact of Inter-Stage Dynamics on Stalling Stage Identification [GT2011‑46668] |
|
Modelling of Soot and NOx in a Full Scale Turbine Engine Combustor With Detailed Chemistry [GT2011‑45084] Validation of an Ignition and Flame Propagation Model for Multiphase Flows [GT2011‑45104] |
|
Numerical Simulations of Confined, Turbulent, Lean, Premixed Flames Using a Detailed Chemistry Combustion Model [GT2011‑45520] |
|
Comparison Between a CFD Code and a Three-Control-Volume Model for Labyrinth Seal Flutter Predictions [GT2011‑46281] |
|
Virtual Gas Turbines: Geometry and Conceptual Description [GT2011‑46437] |
|
Operating Experience on Advanced Technology AE64.3A Gas Turbine [GT2011‑45563] |
|
A Data Analytics Approach to Failure Precursor Detection of Gas Turbine [GT2011‑46019] |
|
Test Results From a Concentrated Solar Microturbine Brayton Cycle Integration [GT2011‑45918] |
|
Synthetic Jet Fuel Combustion: Experimental and Kinetic Modeling Study [GT2011‑45234] |
|
Temporal and Convective Inertia Effects in Plain Journal Bearings With Eccenctricity, Velocity and Acceleration [GT2011‑45880] |
|
Experimental Study and Optimization of a 2.44 Meter Vertical Axis Wind Turbine [GT2011‑46605] |
|
A Study on the Influence of Hole’s Diameter With Holed Casing Treatment [GT2011‑46167] |
|
New Locking Arrangement for Radial Entry Turbine Blades [GT2011‑45581] |
|
Laminar Flame Velocity of Components of Natural Gas [GT2011‑46312] |
|
The Influence of Turbine Stator Well Coolant Flow Rate and Passage Configuration on Cooling Effectiveness [GT2011‑46448] |
|
Heat Transfer in Turbine Hub Cavities Adjacent to the Main Gas Path Including FE-CFD Coupled Thermal Analysis [GT2011‑45695] |
|
Effect of Surface Texturing on the Steady-State Properties and Dynamic Coefficients of a Plain Journal Bearing: Experimental Study [GT2011‑46804] |
|
Comparison of the Steady-State and Dynamic Performance of Two Fixed-Geometry Journal Bearings [GT2011‑46761] |
|
Wall Shear Stress Measurements on a Highly Loaded Compressor Cascade [GT2011‑46364] |
|
Experimental Studies of Crude Oil Combustion in a Top-Mounted Silo Combustor [GT2011‑45248] |
|
Effects of Multiple-Injection-Burner Configurations on Combustion Characteristics for Dry Low-NOx Combustion of Hydrogen-Rich Fuels [GT2011‑45295] Combustion Characteristics of a Multiple-Injection Combustor for Dry Low-NOx Combustion of Hydrogen-Rich Fuels Under Medium Pressure [GT2011‑45459] |
|
Breakup of Liquid Jets Emerging From Elliptic Orifices [GT2011‑45390] |
|
Elastomer Compatibility Test of Alternative Fuels Using Stress-Relaxation Test and FTIR Spectroscopy [GT2011‑46100] |
|
Supporting Windpower Within a Separate Electric Power Grid [GT2011‑46494] |
|
The Effects of Improved Starting Capability on Energy Yield for Small HAWTs [GT2011‑45674] Time Resolved Measurements in the Durham Cascade [GT2011‑45838] |
|
Computational Study of Kelvin-Helmholtz Instability Created by Interaction of the Mainstream Flow and the Seal Flow in Gas Turbines [GT2011‑45284] |
|
Assessment of Current Chemiluminescence Kinetics Models at Engine Conditions [GT2011‑45914] |
|
Vibration Control of a Turbo Molecular Pump Suspended by Active Magnetic Bearings [GT2011‑45785] |
|
Lifing Requirement Based Turbine Airfoil Mass Estimation Method in Conceptual Aero-Engine Design [GT2011‑45613] The Architecture and Application of Preliminary Design Systems [GT2011‑45614] |
|
Influence of Variable Geometry Transients on the Gas Turbine Performance [GT2011‑46565] |
|
Impeller–Vaned Diffuser Interaction in a Centrifugal Compressor at the Best Efficiency Point [GT2011‑46223] Impeller–Vaned Diffuser Interaction in a Centrifugal Compressor at Off Design Conditions [GT2011‑46234] |
|
The Influence of Blade Sweep Technique in Linear Cascade Configuration [GT2011‑45728] |
|
Marine Gas Turbine Performance Model for More Electric Ships [GT2011‑46101] |
|
Temporal and Convective Inertia Effects in Plain Journal Bearings With Eccenctricity, Velocity and Acceleration [GT2011‑45880] |
|
A Low-Order Modelling of Ducted Flames With Temporally Varying Equivalence Ratio in Realistic Geometries [GT2011‑45255] |
|
Flexible Non-Intrusive Heat Flux Instrumentation for the AFRL Research Turbine [GT2011‑46853] |
|
Conjugate Heat Transfer Analysis for a Film-Cooled Turbine Vane [GT2011‑45920] |
|
Remaining Life Assessment Technology Applied to Steam Turbines and Hot Gas Expanders [GT2011‑45324] |
|
Remaining Life Assessment Technology Applied to Steam Turbines and Hot Gas Expanders [GT2011‑45324] |
|
Novel Dynamic Rotor and Blade Deformation and Vibration Monitoring Technique [GT2011‑45346] |
|
LES of Pre-Vaporised Kerosene Combustion at High Pressures in a Single Sector Combustor Taking Advantage of FGM [GT2011‑45819] |
|
Removals for Cause: A 35 Year Assessment of LM2500 Engine Removals by the United States Navy [GT2011‑45031] |
|
Effect of Tip Clearance on the Prediction of Non-Synchronous Vibrations in Axial Compressors [GT2011‑45392] |
|
A Simplified CFD Model With Multi-Periodic Boundary Conditions for Cross Wavy Channels [GT2011‑46050] |
|
A Quasi-One-Dimension CFD Model for Multistage Compressor [GT2011‑45497] |
|
Numerical Study on Varied Vortex Reducer Configurations for the Flow Path Optimization in Compressor Cavities [GT2011‑45975] |
|
Simulations and Measurements of the Flow and Noise in Hot Supersonic Jets [GT2011‑45368] |
|
Optimization of Wind Turbine Blades Using Lifting Surface Method and Genetic Algorithm [GT2011‑46066] |
|
Numerical Simulation of Surge in Turbocharger Centrifugal Compressor: Influences of Downstream Plenum [GT2011‑45163] |
|
A One-Dimensional Investigation of the Effect of an Active Control Turbocharger on Internal Combustion Engine Performance [GT2011‑46599] |
|
A LES Based Sound Absorption Analysis of High-Amplitude Waves Through an Orifice With Bias Flow [GT2011‑45639] Effect of Fuel Distribution on Spray Dynamics in a Two-Staged Multi-Injection Burner [GT2011‑46519] |
|
Experimental Analysis of Simultaneous Non-Harmonically Related Unstable Modes in a Swirled Combustor [GT2011‑46701] |
|
Massively Parallel DNS and LES of Turbine Vane Endwall Horseshoe Vortex Dynamics and Heat Transfer [GT2011‑45915] |
|
Gas Path Analysis on KLM In-Flight Engine Data [GT2011‑45625] |
|
Investigation of the Influence of Different Rim Seal Geometries in a Low-Pressure Turbine [GT2011‑45682] |
|
Separation of Particles in the Secondary Air System of Gas Turbines [GT2011‑45080] Design and Validation of a New Test Rig for Brush Seal Testing Under Engine Relevant Conditions [GT2011‑45107] Experimental Investigation of Lubrication Oil Film Dynamics in a Typical Aero-Engine Bearing Chamber Environment [GT2011‑45545] Modelling of an Aero Engine Bearing Chamber Using Enhanced CFD Technique [GT2011‑45635] |
|
Passive Tracer Validity for Cooling Effectiveness Modeling in a Turbine Rim Seal Environment [GT2011‑45654] |
|
Controlled Fan Blade Tip/Shroud Rubs at Engine Conditions [GT2011‑45223] |
|
Heat Transfer for the Film-Cooled Vane of a 1-1/2 Stage High-Pressure Transonic Turbine: Part I—Experimental Configuration and Data Review With Inlet Temperature Profile Effects [GT2011‑46570] Heat Transfer for the Film-Cooled Vane of a 1-1/2 Stage High-Pressure Transonic Turbine: Part II—Effect of Cooling Variation on the Vane Airfoil and Inner Endwall [GT2011‑46573] |
|
Inlet Guide Vane Failure: Aero-Mechanical and System Control Interaction Effect [GT2011‑46742] |
|
Experimental Determination of Flame Transfer Function Using Random Velocity Perturbations [GT2011‑45881] |
|
Effect of Mixing Quality on NOx Emissions in Reheat Combustion of GT24 and GT26 Engines [GT2011‑45676] |
|
Numerical Investigations of a Swirl-Stabilized Premixed Flame at Ultra-Wet Conditons [GT2011‑45866] |
|
Aeroelastic Stability Assessment of an Industrial Compressor Blade Including Mistuning Effects [GT2011‑45800] |
|
Supporting Windpower Within a Separate Electric Power Grid [GT2011‑46494] |