|
Design of an Aero Gas Turbine Engine Gearbox Power Transmission Spline-Spigot Joint [GT2011‑45278] |
|
Design of an Aero Gas Turbine Engine Gearbox Power Transmission Spline-Spigot Joint [GT2011‑45278] |
|
Experimental Studies of Bifurcations Leading to Chaos in a Laboratory Scale Thermoacoustic System [GT2011‑46149] Investigation of Subcritical Instability in Ducted Premixed Flames [GT2011‑46155] |
|
Evolution of the DDG 51 Machinery Control System to Support SSGTG Local Controller Upgrades [GT2011‑46849] |
|
Experimental Investigation of Louver Cooling Scheme on Gas Turbine Vane Suction Side [GT2011‑45585] |
|
Vaporization Characteristics of Ethanol Droplets: Influence of the Environment Humidity [GT2011‑46531] |
|
Heat Transfer for the Film-Cooled Vane of a 1-1/2 Stage High-Pressure Transonic Turbine: Part I—Experimental Configuration and Data Review With Inlet Temperature Profile Effects [GT2011‑46570] Heat Transfer for the Film-Cooled Vane of a 1-1/2 Stage High-Pressure Transonic Turbine: Part II—Effect of Cooling Variation on the Vane Airfoil and Inner Endwall [GT2011‑46573] |
|
Geometry Optimization of Textured 3D Micro-Thrust Bearings [GT2011‑45822] |
|
More Electric Engine Architecture for Aircraft Engine Application [GT2011‑46765] |
|
Challenges in Uncertainty, Calibration, Validation and Predictability of Engineering Analysis Models [GT2011‑46554] |
|
Integrated Combustor - Turbine Design for Improved Aerothermal Performance: Effect of Dilution Air Control [GT2011‑46354] |
|
Design Considerations for Axial Steam Turbine Rotor Inlet Cavity Volume and Length Scale [GT2011‑45127] Marine Gas Turbine Performance Model for More Electric Ships [GT2011‑46101] |
|
Gas Turbine Emissions Characteristics in Perfectly Premixed Combustion [GT2011‑46470] |
|
Improved Map Scaling Methods for Small Turbocharger Compressors [GT2011‑45345] Numerical Investigation of Aerodynamic Radial and Axial Impeller Forces in a Turbocharger [GT2011‑46360] Secondary Flow Structures and Losses in a Radial Turbine Nozzle [GT2011‑46753] |
|
Integrated Preliminary Design Approach for Turbomachinery Design [GT2011‑45546] |
|
Study on Vibration Characteristics of Single Crystal Blade and Directionally Solidified Blade [GT2011‑45032] |
|
Dynamic Characteristic Analysis of a Rotor Bearing System Using Global Assumed Mode Method With Different Polynomial Functions [GT2011‑46293] |
|
Impact of Steam Injection and Turbine Exhaust Gas Bypass in the Recuperative Cycle Gas Turbine CHP System [GT2011‑46375] |
|
Design and Experimental Study of Organic Rankine Cycle (ORC) and Radial Turbine [GT2011‑46152] |
|
Thermal Analysis of Cooling System in a Gas Turbine Transition Piece [GT2011‑45961] |
|
Aerodynamic and Aerothermal Investigation of the Flow Around an HPT Rotor Shroud: PIV Measurements [GT2011‑45977] Aerodynamic and Aerothermal Investigation of the Flow Around an HPT Rotor Shroud: Heat Transfer and Cooling Effectiveness [GT2011‑45979] |
|
Effect of GTL-Like Jet Fuel Composition on GT Engine Altitude Ignition Performance: Part I—Combustor Operability [GT2011‑45487] Investigation of GTL-Like Jet Fuel Composition on GT Engine Altitude Ignition and Combustion Performance: Part II—Detailed Diagnostics [GT2011‑45510] |
|
Rotor Tip Flow-Field Near Inception Point of Rotating Instability in an Axial-Flow Fan [GT2011‑45338] Improvement in Efficiency and Stall Margin of Centrifugal Blower Impeller by Multi-Objective Optimization [GT2011‑45351] |
|
PIV Study on the Dimple Mid-Plane of a Narrow Rectangular Channel With Dimples Applied to One Wall [GT2011‑46132] The Effect of Transpiration on Discrete Injection for Film Cooling [GT2011‑46138] A Study of Heat Transfer Augmentation for Recuperative Heat Exchangers: Comparison Between Two Dimple Geometries [GT2011‑46401] Impact of a Collector Box on the Pressure Recovery of an Exhaust Diffuser System [GT2011‑46455] Interaction of Rotational Wakes and Coolant Film in a Sector-Annular Duct [GT2011‑46465] |
|
Experimental and Numerical Study of NOx Formation From the Lean Premixed Combustion of CH4 Mixed With CO2 and N2 [GT2011‑45090] |
|
Gas Turbine Emissions Characteristics in Perfectly Premixed Combustion [GT2011‑46470] |
|
Energy and Exergy Analysis of Thermoacoustics Assisted Gas Turbine Engines [GT2011‑45604] |
|
CFD Simulations of Flow and Heat Transfer in a Pre-Swirl System: Influence of Rotating-Stationary Domain Interface [GT2011‑45085] |
|
Sound Deadening on Fans [GT2011‑45004] |
|
Analysis of NOx Formation in an Axially Staged Combustion System at Elevated Pressure Conditions [GT2011‑45239] |
|
Low-Frequency Thermoacoustic Instability Mitigation Using Adaptive-Passive Acoustic Radiators [GT2011‑46642] Distributed Parameter Acoustic Modeling of a Perforation With Bias Flow [GT2011‑46649] |
|
Effects of Nonuniform Reactant Stoichiometry on Combustion Instability [GT2011‑45097] |
|
Experimental Investigation of the Influence of Water Injection on Acoustic Properties of the Exhaust System of a Gas Turbine Combustion Test Rig [GT2011‑46366] |
|
An Experimental and Modeling Study of Laminar Flame Speeds of Alternative Aviation Fuels [GT2011‑45606] |
|
The Effect of the Casing Movement Relative to the Blades on the Tip Leakage Loss in Axial Flow Compressors [GT2011‑46182] CFD Modeling Effects on Unsteady Multistage Simulation for a Transonic Axial Compressor [GT2011‑46198] The Influence of Shrouded Stator Cavity Flows on the Aerodynamic Performance of a High-Speed Multistage Axial-Flow Compressor [GT2011‑46300] |
|
The Effect of the Casing Movement Relative to the Blades on the Tip Leakage Loss in Axial Flow Compressors [GT2011‑46182] |
|
System Analysis of IGFC With Exergy Recuperation Utilizing Low-Grade Coal [GT2011‑46282] |
|
A Residual Stress Measurement Technique for Turbine Blade Dovetails [GT2011‑45352] |
|
The NEKOMIMI Cooling Technology: Cooling Holes With Ears for High-Efficient Film Cooling [GT2011‑45524] |
|
CFD Modeling Effects on Unsteady Multistage Simulation for a Transonic Axial Compressor [GT2011‑46198] |
|
Design and Aerodynamic Analysis a Highly Loaded Helium Compressor [GT2011‑46044] |
|
Combustor Design Optimisation Using Co-Kriging of Steady and Unsteady Turbulent Combustion [GT2011‑46420] |
|
Thermal Properties and Phase Analysis of Titania Doped Yttria-Zirconia Ceramics for Use as High Temperature Thermal Barrier Coatings (TBCS) [GT2011‑45054] Mechanical Properties of Titania-Doped Yttria Stabilized Zirconia (TiYSZ) for Use as Thermal Barrier Coating (TBC) [GT2011‑45643] |
|
A Validation of Commerical Flow Solver Performance on Hybridised Octree Meshes [GT2011‑45713] |
|
Determination of Crack Initiation on L-1 LP Steam Turbine Blades: Part 2—Computational Analyses [GT2011‑46206] |
|
Compressible and Incompressible Large Eddy Simulation of a Premixed Dump Combustor [GT2011‑45304] |
|
Flexible Non-Intrusive Heat Flux Instrumentation for the AFRL Research Turbine [GT2011‑46853] |
|
Application of an Inverse Design Method to Meet a Target Pressure in Axial-Flow Compressors [GT2011‑46091] Investigation of Geometry, Total Condition and Waves Effect on Two Phase Liquid-Vapor Flow Using Equilibrium Thermodynamics [GT2011‑46648] |
|
Characteristics of an Ultra-Lean Swirl Combustor Flow by LES and Comparison to Measurements [GT2011‑45300] |
|
Mechanical Design of Highly Loaded Large Steam Turbines [GT2011‑45703] |
|
Amplified Pressure Transducer Using SOI Sensors and SOI Electronics, Suitable for High Temperature Operation (250°C) [GT2011‑45704] |
|
Diagnostics of Highly Degraded Industrial Gas Turbines Using Bayesian Networks [GT2011‑45249] Ultra High Bypass Ratio Engine Sizing and Cycle Selection Study for a Subsonic Commercial Aircraft in the N+2 Timeframe [GT2011‑45370] NPSS Volume Dynamic Capability for Real-Time Physics Based Engine Modeling [GT2011‑45374] A Gas Turbine Engine Model of Transient Operation Across the Flight Envelope [GT2011‑45565] Model Based Data Reconciliation and Bias Detection for Heavy-Duty Industrial Gas Turbines Performance Diagnosis [GT2011‑45943] |
|
Heat Transfer, Hydrodynamics and Pressure Drop in the Model of a Blade Leading Edge Cyclone Cooling [GT2011‑45150] Heat Transfer and Friction Factor in the Rib Roughened Blade Leading Edge Cooling Passage [GT2011‑45434] |
|
A Hybrid EKF-Fuzzy Approach to Fault Detection and Isolation of Industrial Gas Turbines [GT2011‑45878] |
|
Noise Prediction of Pressure-Mismatched Jets Using Unstructured Large Eddy Simulation [GT2011‑46548] |
|
Investigation of Cooling Effectiveness of Gas Turbine Inlet Fogging Location Relative to the Silencer [GT2011‑46809] |
|
Implication of Different Fuel Injector Configurations for Hydrogen Fuelled Micromix Combustors [GT2011‑46845] |
|
Elements of Dynamic Characterization of a Bladed Disk by Using the Tip-Timing Method Under Vacuum Conditions [GT2011‑46435] |
|
Forced Response of Bladed Disks With Mistuning Damping [GT2011‑45802] |
|
Nonlinear Fault Diagnosis of Jet Engines by Using a Multiple Model-Based Approach [GT2011‑45143] |
|
Thermal Properties and Phase Analysis of Titania Doped Yttria-Zirconia Ceramics for Use as High Temperature Thermal Barrier Coatings (TBCS) [GT2011‑45054] Mechanical Properties of Titania-Doped Yttria Stabilized Zirconia (TiYSZ) for Use as Thermal Barrier Coating (TBC) [GT2011‑45643] |
|
An Experimental and Modeling Study of Laminar Flame Speeds of Alternative Aviation Fuels [GT2011‑45606] |
|
Supersonic Ejectors for Hydrocarbon Emissions Capture [GT2011‑46443] |
|
Combustor and Augmentor Combustion Modeling for LES Based on Stochastic Model Parameterization [GT2011‑45126] |
|
Mechanical Property Variability of Cast Ni-Base Superalloy IGT Components [GT2011‑45743] |
|
Heat Transfer Characteristics of a Non-Rotating Two-Pass Rectangular Duct With Various Guide Vanes in the Tip Turn Region [GT2011‑45962] |
|
Construction of Shock Response Map for a Flexible Rotor-Bearing System With Mount System to Base Excitations Using the FE Transient Analysis Method [GT2011‑45339] |
|
Effects of Mesh Density on Static Load Performance of Metal Mesh Gas Foil Bearings [GT2011‑46589] |
|
Imbalance Response of a Rotor Supported by Hybrid Air Foil Bearings [GT2011‑45576] |
|
Development of GUI Type On-Line Condition Monitoring Program for a Turboprop Engine Using LabVIEW® [GT2011‑45337] |
|
Optimization of a Transonic Axial Compressor Considering Interaction of Blade and Casing Treatment to Improve Operating Stability [GT2011‑45404] |
|
Development of GUI Type On-Line Condition Monitoring Program for a Turboprop Engine Using LabVIEW® [GT2011‑45337] |
|
Multi-Objective Optimization of Film-Cooling Holes Considering Heat Transfer and Aerodynamic Loss [GT2011‑45402] Optimization of a Transonic Axial Compressor Considering Interaction of Blade and Casing Treatment to Improve Operating Stability [GT2011‑45404] |
|
Effects of Nonuniform Reactant Stoichiometry on Combustion Instability [GT2011‑45097] |
|
Thermal Analysis of Cooling System in a Gas Turbine Transition Piece [GT2011‑45961] |
|
New Alstom Monitoring Systems Leveraging Artificial Neural Network Technologies [GT2011‑45990] Early Warning of Gas Turbine Failure by Nonlinear Feature Extraction Using an Auto-Associative Neural Network Approach [GT2011‑45991] |
|
Development of the 5MW Power Generation Gas Turbine Engine [GT2011‑45778] |
|
Multi-Objective Optimization of Film-Cooling Holes Considering Heat Transfer and Aerodynamic Loss [GT2011‑45402] |
|
Impact of Steam Injection and Turbine Exhaust Gas Bypass in the Recuperative Cycle Gas Turbine CHP System [GT2011‑46375] |
|
Rotordynamic Performance of an Oil-Free Turboblower Focusing on Load Capacity of Gas Foil Thrust Bearings [GT2011‑46471] Thermal Performance of a Bump Type Gas Foil Bearing Floating on a Hollow Shaft for Increasing Rotating Speed and Static Load [GT2011‑46499] Effects of Mesh Density on Static Load Performance of Metal Mesh Gas Foil Bearings [GT2011‑46589] |
|
Rotordynamic Performance of an Oil-Free Turboblower Focusing on Load Capacity of Gas Foil Thrust Bearings [GT2011‑46471] Effects of Mesh Density on Static Load Performance of Metal Mesh Gas Foil Bearings [GT2011‑46589] |
|
Experiments on Aft-Disk Cavity Ingestion in a Model 1.5-Stage Axial-Flow Turbine [GT2011‑45895] |
|
Performance Evaluation of an Unsteady Turbine Driven by a Pulsed Detonation Combustor [GT2011‑45396] An Investigation of Reynolds Lapse Rate for Highly Loaded Low Pressure Turbine Airfoils With Forward and Aft Loading [GT2011‑46328] |
|
Improvement on Ignition Performance for a Lean Staged Low NOx Combustor [GT2011‑46187] Suppression of NOx Emission of a Lean Staged Combustor for an Aircraft Engine [GT2011‑46256] |
|
Mechanical Design of Highly Loaded Large Steam Turbines [GT2011‑45703] |
|
Aerothermal Investigations on Mixing Flow Field of Film Cooling With Swirling Coolant Flow [GT2011‑46838] |
|
Effect of Variable Guide Vanes and Natural Gas Hybridization for Accommodating Fluctuations in Solar Input to a Gas Turbine [GT2011‑45331] |
|
Low Emissions Power Generation Using Natural Gas Condensates [GT2011‑46674] |
|
Impact on Adiabatic Film Cooling Effectiveness Using Internal Cyclone Cooling [GT2011‑45120] |
|
New Alstom Monitoring Systems Leveraging Artificial Neural Network Technologies [GT2011‑45990] Early Warning of Gas Turbine Failure by Nonlinear Feature Extraction Using an Auto-Associative Neural Network Approach [GT2011‑45991] |
|
Mechanical Property Variability of Cast Ni-Base Superalloy IGT Components [GT2011‑45743] |
|
Lifing Requirement Based Turbine Airfoil Mass Estimation Method in Conceptual Aero-Engine Design [GT2011‑45613] |
|
Altitude Testing of the E3E Core Engine [GT2011‑45876] |
|
Parametric Study of Emissions From Low Calorific Value Syn-Gas Combustion, With Variation of Fuel Distribution, in a Prototype Three Sector Burner [GT2011‑45689] Experimental Investigations of Lean Stability Limits of a Prototype Syngas Burner for Low Calorific Value Gases [GT2011‑45694] |
|
Hydroprocessed Renewable Jet Fuel Evaluation, Performance, and Emissions in a T-63 Turbine Engine [GT2011‑46572] |
|
Experimental Investigation of Lubrication Oil Film Dynamics in a Typical Aero-Engine Bearing Chamber Environment [GT2011‑45545] |
|
On the Effect of Pressure Oscillations on Droplet Autoignition [GT2011‑45008] |
|
Prognostics and Health Management of Aircraft Engine EMA Systems [GT2011‑46537] |
|
Investigations on the Influence of Altitude Conditions on Mixed Exhaust Systems [GT2011‑46175] |
|
Determination of Equivalence Ratio and Oscillatory Heat Release Distributions in Non-Premixed Bluff Body-Stabilized Flames Using Chemiluminescence Imaging [GT2011‑45579] |
|
Application of a Miniature Telemetry System in a Small Gas Turbine Engine [GT2011‑45910] |
|
Altitude Testing of the E3E Core Engine [GT2011‑45876] |
|
Hot Acoustic-Testrig (HAT): A Unique Facility for Thermoacoustic Research [GT2011‑45705] |
|
Improvement of Oxide/Oxide CMC and Development of Combustor and Turbine Components in the HiPOC Program [GT2011‑45460] |
|
Improvement on Ignition Performance for a Lean Staged Low NOx Combustor [GT2011‑46187] Suppression of NOx Emission of a Lean Staged Combustor for an Aircraft Engine [GT2011‑46256] |
|
Improvement of Oxide/Oxide CMC and Development of Combustor and Turbine Components in the HiPOC Program [GT2011‑45460] |
|
Conjugate Heat Transfer Analysis for a Film-Cooled Turbine Vane [GT2011‑45920] |
|
Laminar Flame Speed Measurements and Modeling of Alkane Blends at Elevated Pressures With Various Diluents [GT2011‑45122] |
|
Enhanced Static-Dynamic Pressure Transducer for the Detection of Acoustic Level Flow Instabilities in Gas Turbine Engines [GT2011‑45750] |
|
System Analysis of IGFC With Exergy Recuperation Utilizing Low-Grade Coal [GT2011‑46282] |
|
The Effect of the Casing Movement Relative to the Blades on the Tip Leakage Loss in Axial Flow Compressors [GT2011‑46182] CFD Modeling Effects on Unsteady Multistage Simulation for a Transonic Axial Compressor [GT2011‑46198] The Influence of Shrouded Stator Cavity Flows on the Aerodynamic Performance of a High-Speed Multistage Axial-Flow Compressor [GT2011‑46300] |
|
Experimental and Analytical Study on the Operation Characteristics of the AHAT System [GT2011‑45168] |
|
Experimental Analysis of Soot Formation and Oxidation in a Gas Turbine Model Combustor Using Laser Diagnostics [GT2011‑45611] |
|
Effects of Multiple-Injection-Burner Configurations on Combustion Characteristics for Dry Low-NOx Combustion of Hydrogen-Rich Fuels [GT2011‑45295] Combustion Characteristics of a Multiple-Injection Combustor for Dry Low-NOx Combustion of Hydrogen-Rich Fuels Under Medium Pressure [GT2011‑45459] |
|
Dynamics of Flames Stabilized by Triangular Bluff Body in Partially Premixed Methane-Air Combustion [GT2011‑46241] Ultra Rich Combustion of Natural Gas to Syngas [GT2011‑46383] |
|
Technology Evolution of Turbofan Engines Based on Patent Analysis: A New Sight to Technology Opportunities [GT2011‑45061] |
|
Comparative Validation Study on Identification of Premixed Flame Transfer Function [GT2011‑46342] |
|
Aerothermal Investigations on Mixing Flow Field of Film Cooling With Swirling Coolant Flow [GT2011‑46838] |
|
Prospects for Application of Ship’s Multi-Module Gas Turbine Engines on the Basis of Ceramic Tunnel Turbomachines [GT2011‑45201] |
|
Study on Fault Diagnostics of a Turboprop Engine Using Inverse Performance Model and Artificial Intelligent Methods [GT2011‑45336] Development of GUI Type On-Line Condition Monitoring Program for a Turboprop Engine Using LabVIEW® [GT2011‑45337] |
|
Integration of Unknown Input Observers and Classification for Turbofan Engine Diagnosis [GT2011‑46429] |
|
Laminar Flame Velocity of Components of Natural Gas [GT2011‑46312] |
|
Assessment of Current Chemiluminescence Kinetics Models at Engine Conditions [GT2011‑45914] |
|
Two and Three-Dimensional Prescribed Surface Curvature Distribution Blade Design (CIRCLE) Method for the Design of High Efficiency Turbines, Compressors, and Isolated Airfoils [GT2011‑46722] Aerodynamic Improvements of Wind-Turbine Airfoil Geometries With the Prescribed Surface Curvature Distribution Blade Design (CIRCLE) Method [GT2011‑46728] |
|
Tip Leakage Losses in Subsonic and Transonic Blade-Rows [GT2011‑45798] |
|
Experimental and Numerical Analysis of High Temperature Gas Turbine Nozzle Vane Convective and Film Cooling Effectiveness [GT2011‑45294] |
|
Separation Control Using Plasma Actuators: Steady Flow in Low Pressure Turbines [GT2011‑46807] |
|
Development and Field Validation of a Large-Frame Gas Turbine Power Train for Steel Mill Gases [GT2011‑45923] |
|
Design and Test of a Highly Loaded Single-Stage High Pressure Turbine [GT2011‑45342] |
|
On a Numerical Method for the Simulation of Steady Jet Array Interaction With Rotating Components [GT2011‑45832] |
|
An Experimental Investigation of Stator Clocking Effects in a Two-Stage Low-Speed Axial Compressor [GT2011‑45680] |
|
Effect of Surface Texturing on the Steady-State Properties and Dynamic Coefficients of a Plain Journal Bearing: Experimental Study [GT2011‑46804] |
|
Marine Gas Turbine Performance Model for More Electric Ships [GT2011‑46101] |
|
Numerical and Experimental Investigations of a Compressor Cascade Flow With Secondary Air Removal [GT2011‑45202] Transition Modelling for Vortex Generating Jets on Low-Pressure Turbine Profiles [GT2011‑45621] |
|
Eddy Current Damper for Turbine Blading: Electromagnetic Finite Element Analysis and Measurement Results [GT2011‑45242] |
|
Optimization of 6.2:1 Pressure Ratio Centrifugal Compressor Impeller by 3D Inverse Design [GT2011‑46505] |
|
Experimental and Numerical Study of NOx Formation From the Lean Premixed Combustion of CH4 Mixed With CO2 and N2 [GT2011‑45090] |
|
Probabilistic Lifetime Assessment of Turbine Vanes [GT2011‑45841] |
|
Emissions Assessment of Alternative Aviation Fuel at Simulated Altitudes [GT2011‑45133] |
|
Experimental Characterization of Low NOx Micromix Prototype Combustors for Industrial Gas Turbine Applications [GT2011‑45305] |
|
Analysis of NOx Formation in an Axially Staged Combustion System at Elevated Pressure Conditions [GT2011‑45239] Measurement of a Benchmarking Jet in Crossflow Configuration Under Highly Turbulent Conditions [GT2011‑45262] |
|
Laminar Flame Speed Measurements and Modeling of Alkane Blends at Elevated Pressures With Various Diluents [GT2011‑45122] |
|
The Influence of Blade Properties on the Forced Response of Mistuned Bladed Disks [GT2011‑46826] |
|
Experimental and Numerical Analysis of High Temperature Gas Turbine Nozzle Vane Convective and Film Cooling Effectiveness [GT2011‑45294] |
|
Application of a Multistage Casing Treatment in a High Speed Axial Compressor Test Rig [GT2011‑46315] |
|
The Simulation of an Axial Flow Fan Performance Curve at Low Flow Rates [GT2011‑45709] |
|
Theory and Application of Axisymmetric Endwall Contouring for Compressors [GT2011‑45624] |
|
Validation of a First Vane Platform Cooling Design [GT2011‑45252] |
|
Numerical Investigations of a Swirl-Stabilized Premixed Flame at Ultra-Wet Conditons [GT2011‑45866] |
|
Fatigue Reliability Predictions for Crack Bridging Materials [GT2011‑46222] |
|
Numerical Investigations on Film Cooling Performances [GT2011‑45775] |
|
Determination of Crack Initiation on L-1 LP Steam Turbine Blades: Part 1—Measurements on Rotor Train, Material Specimens and Blades [GT2011‑46203] Determination of Crack Initiation on L-1 LP Steam Turbine Blades: Part 2—Computational Analyses [GT2011‑46206] |
|
A Numerical Method for Turbulent Flows in Highly Staggered and Low Solidity Supersonic Turbine Cascades [GT2011‑45450] Reduced Modelling for Turbine Rotor-Blade Coupled Bending Vibration Analysis [GT2011‑45776] |
|
LP Turbine Secondary Vortices: Reynolds Lapse [GT2011‑45557] |
|
Adjoint-Based Flow Sensitivity Analyis Using Arbitrary Control Surfaces [GT2011‑45041] Roughness Modeling for Turbomachinery [GT2011‑45424] Steady State Versus Time-Accurate CFD in an Automated Airfoil Section Optimization of a Counter Rotating Fan Stage [GT2011‑46190] |
|
Experimental and Numerical Analyses of Radial Turbine Blisks With Regard to Mistuning [GT2011‑45359] Modal and Aeroelastic Analysis of a Compressor Blisk Considering Mistuning [GT2011‑45849] |
|
Improving Rotordynamic Performance of an Axial Flow Compressor With Two-Lobe Bearings Using Nonlinear Constraint Parameter Optimization [GT2011‑45311] |
|
Measured Static and Rotordynamic Coefficient Results for a Rocker-Pivot Pad TP Bearing With 50 and 60% Offsets [GT2011‑45209] |
|
Potential Flow Field Generated by Downstream Moving Bars and Propagated on a Turbine Blade at Low Reynolds Number [GT2011‑46433] |
|
Virtual Gas Turbines: Geometry and Conceptual Description [GT2011‑46437] |
|
Advanced Gas Turbine Diagnostics Using Pattern Recognition [GT2011‑45670] |
|
Non-Linearities in an Aero Engine Casing Assembly: A Case Study [GT2011‑45452] |
|
Design of an Aero Gas Turbine Engine Gearbox Power Transmission Spline-Spigot Joint [GT2011‑45278] Non-Linearities in an Aero Engine Casing Assembly: A Case Study [GT2011‑45452] |
|
Dry Friction Whip and Whirl Predictions for a Rotor-Stator Model With Rubbing Contact at Two Locations [GT2011‑45081] |
|
Thermodynamic and Kinetic Modeling of Precipitation Phenomena in P9 Steels [GT2011‑46586] |
|
Design Optimization of a Retractable Holder for Compressor Discharge Brush Seal [GT2011‑45756] |
|
Numerical Comparison of Heat Transfer and Pressure Drop in Gas Turbine Blade Cooling Channels With Dimples and Rib-Turbulators [GT2011‑45277] |
|
Dynamics of Flames Stabilized by Triangular Bluff Body in Partially Premixed Methane-Air Combustion [GT2011‑46241] |
|
Diagnostics of Highly Degraded Industrial Gas Turbines Using Bayesian Networks [GT2011‑45249] |
|
Experimental and Numerical Investigation of Tip Clearance and Bleed Effects in a Centrifugal Compressor Stage With Pipe Diffuser [GT2011‑45128] |
|
Simulations and Measurements of the Flow and Noise in Hot Supersonic Jets [GT2011‑45368] |
|
System Analysis of IGFC With Exergy Recuperation Utilizing Low-Grade Coal [GT2011‑46282] |
|
Shot Peening Effect on Low Cycle Fatigue Properties of Ti-6Al-4V and Inconel 718 [GT2011‑46847] |
|
Combustion Characteristics of Fuel Staged Combustor for Aeroengines at LTO Cycle Conditions [GT2011‑46133] |
|
Fouling Mechanisms in Axial Compressors [GT2011‑45012] Particle Transport Analysis of Sand Ingestion in Gas Turbine Engines [GT2011‑45057] |
|
Correlations Hidden in Compressor Maps [GT2011‑45519] |
|
Influence of Unsteady Turbine Flow on the Performance of an Exhaust Diffuser [GT2011‑45673] |
|
Behaviour of Spray in a Twin-Fluid Atomizer [GT2011‑46162] |
|
The NEKOMIMI Cooling Technology: Cooling Holes With Ears for High-Efficient Film Cooling [GT2011‑45524] |
|
Experimental Analysis of Confined Jet Flames by Laser Measurement Techniques [GT2011‑45111] |
|
Minimizing Pressure Pulsations in a Centrifugal Compressor [GT2011‑46697] |
|
Minimising Loss in a Heat Exchanger Installation for an Intercooled Turbofan Engine [GT2011‑45814] |
|
Experimental and Numerical Investigation of Different Rectangular Volute Geometries for Large Radial Compressors [GT2011‑46296] |
|
Conceptual Design and Mission Analysis for a Geared Turbofan and an Open Rotor Configuration [GT2011‑46451] |